JET · 719400K
Ready to buy
The retained reference is $2,749 current authorized U.S. price. Confirm the K package with cast-iron legs and freight; extension, chuck, extraction and mobility are separate. Confirm workholding, circuit, floor or bench, unloading, safe blank range, PPE, maintenance and parts before payment.
Current market
Each line carries its own check date because price, software, specifications, and product cycle do not age at the same speed.
Confirm the K package with cast-iron legs and freight; extension, chuck, extraction and mobility are separate. Confirm stock, freight, liftgate, tax, promotion, return and authorized U.S. support at checkout.
JWL-1440VSK is the specialist choice when 40-inch stock spindle capacity and a sliding, pivoting head matter more than very low roughing speed, electronic VFD control or compact footprint.
Other paths
These are not generic competitors. Each one represents a different way to buy into the same market.
Harvey
Laguna Tools
What changed
Older observations stay in the ledger when the current view changes. That lets a buyer tell the difference between an old complaint, an active issue, and a problem that was corrected.
JWL-1440VSK 14-Inch by 40-Inch Lathe with Legs was checked against manufacturer identity, manual, parts or support, exact current U.S. price, independent woodworking evidence and bounded owner evidence.
Each amount stays tied to its source and capture date. Conflicting prices remain visible until the seller resolves them.
Current reference priceA structured timeline will begin with the next source capture
Owner experience
Owner evidence is retained as a delivery, setup, control, workholding, maintenance and service checklist for JWL-1440VSK 14-Inch by 40-Inch Lathe with Legs, not a performance, capacity, defect or safety rate.
Reports are self-selected and span different serials, voltages, stands, benches, chucks, blanks, speeds, accessories, circuits, dust conditions, service regions, skill and maintenance. They cannot prove population reliability, runout, finish, safe capacity, code compliance, service rate or injury prevention.Self-selected exact-model owners discuss delivery, setup, alignment, controls, vibration, accessories, maintenance, failures and service. Reports are configuration-specific anecdotes, not performance, defect, capacity or safety rates.
Choose it for its geometry and accept the mechanical-drive maintenance and high minimum speed as first-order constraints
1 evidence recordSources
The page separates what a source states directly from what we conclude across sources.
JET identifies 719400K as a 14-by-40-inch 1 HP floor machine whose headstock slides and pivots through seven positions, using a 400 to 3,000 RPM Reeves mechanical variable-speed drive.
Ohio Power Tool lists 719400K at $2,749 with legs. Confirm the K package with cast-iron legs and freight; extension, chuck, extraction and mobility are separate
Approximately 14-1/2-inch swing and 40 inches between centers; the optional extension can reach about 60 inches between centers or support documented outboard positions. 1 HP dual-voltage 115 or 230 V motor with Reeves mechanical variable speed from 400 to 3,000 RPM. Speed changes occur while running as instructed, and the 400 RPM floor constrains irregular large blanks. 1-inch by 8 TPI spindle, MT2 tapers, 36-position indexing, 3/8-inch bore and Acme-thread tailstock; exact rest and quill dimensions remain in the manual.
JET publishes parts, service and five-year limited warranty support. Retain the exact 719400K manual and budget Reeves-belt and lubrication maintenance rather than assuming VFD behavior. The 719400K package includes legs and core centers, rest and faceplate equipment specified by JET. Chuck, extension, mobile base, tools, extraction and PPE are separate.
AAW recommends a full face shield, conservative startup speed, slower speeds for larger or rough work, locked tailstock and tool-rest assemblies and no gloves, loose clothing, jewelry or untied hair.
OSHA identifies rotating parts, point-of-operation contact, flying chips and thrown work, and addresses close tool-rest placement, guards and entanglement controls. Application to a shop depends on workplace and operation.
OSHA notes high-velocity wood-dust emission and recommends close source capture. A lathe package does not establish exposure control or compliance.
Fine Woodworking tested the exact 1440VSK under heavy spindle and bowl cuts and documented the Reeves-drive tradeoff. One test sample does not guarantee power, alignment or finish.
Self-selected exact-model owners discuss delivery, setup, alignment, controls, vibration, accessories, maintenance, failures and service. Reports are configuration-specific anecdotes, not performance, defect, capacity or safety rates.
TURBO T-40 14-Inch by 24-Inch Lathe is the compact industrial servo-motor lathe alternative at $2,399 current direct promotional U.S. price.
Revo 18|36 Lathe 220V is the mainstream 2 hp sliding-head vfd floor lathe alternative at $3,649 current direct U.S. price.
Manufacturer identity, exact current U.S. price, manual or specification, parts or support path, independent woodworking evidence and bounded owner or turner evidence were checked on August 20, 2026. This market covers complete current U.S.-supported benchtop, midi and full-size woodturning lathes for serious hobby and professional shops. It excludes metal lathes, duplicators and copy lathes, accessories, extensions and stands sold alone, unsupported imports, obsolete machines, cosmetic packages, chuck bundles and minor swing, bed or voltage siblings used only to pad the count. Preserve swing over bed and banjo, actual between-centers geometry, headstock and bed position, motor input and claimed output, voltage, phase, circuit and plug, belt ranges and electronic control, lowest usable speed, forward and reverse conditions, spindle thread and shoulder, taper, bore, indexing, quill and travel, fixed, sliding, swiveling and outboard paths, extension and rest support, weight, stand, floor, mobility and lifting, tool rest, banjo and tailstock behavior, included faceplate and centers versus required chuck, jaws, tools and sharpening, center alignment, runout, bed twist, setup and break-in, dust, chips, noise, electrical cooling, parts, warranty and service. A headline swing or horsepower figure does not approve a blank. Safe RPM depends on diameter, balance, soundness, mounting, drive and operator skill. Inspect stock and glue joints, rotate by hand, start at the lowest stable speed while standing out of the rotation plane, keep a locked rest close to the work and stop for vibration. Use impact-rated eye protection plus a full face shield, tie hair, remove loose clothing and jewelry and never wear gloves near rotating work. Guards, extraction, respiratory protection, hearing protection, electrical work, permits, workplace rules, fire control, rigging and training remain site-specific. Reverse can loosen threaded workholding unless positively secured as documented. Dust collection does not capture every chip or respirable particle. No manufacturer claim, capacity, price, review, owner report, drive feature, brake, jam sensor, guard, mounting system or service plan guarantees surface finish, runout, production capacity, uptime, code or workplace compliance, dust or noise control, workpiece retention, injury prevention or any safety outcome.
Researching another model?