Harvey · T-40
Ready to buy
The retained reference is $2,399 current direct promotional U.S. price. Promotion can change; cast-iron legs, outboard support and 18-inch extension are separate, and freight is calculated at checkout. Confirm workholding, circuit, floor or bench, unloading, safe blank range, PPE, maintenance and parts before payment.
Current market
Each line carries its own check date because price, software, specifications, and product cycle do not age at the same speed.
Promotion can change; cast-iron legs, outboard support and 18-inch extension are separate, and freight is calculated at checkout. Confirm stock, freight, liftgate, tax, promotion, return and authorized U.S. support at checkout.
T-40 suits turners who want servo response, low 60 RPM control and premium compact construction while accepting a proprietary electronics and accessory path plus a separate leg set.
Other paths
These are not generic competitors. Each one represents a different way to buy into the same market.
NOVA
JET
What changed
Older observations stay in the ledger when the current view changes. That lets a buyer tell the difference between an old complaint, an active issue, and a problem that was corrected.
TURBO T-40 14-Inch by 24-Inch Lathe was checked against manufacturer identity, manual, parts or support, exact current U.S. price, independent woodworking evidence and bounded owner evidence.
Each amount stays tied to its source and capture date. Conflicting prices remain visible until the seller resolves them.
Current reference priceA structured timeline will begin with the next source capture
Owner experience
Owner evidence is retained as a delivery, setup, control, workholding, maintenance and service checklist for TURBO T-40 14-Inch by 24-Inch Lathe, not a performance, capacity, defect or safety rate.
Reports are self-selected and span different serials, voltages, stands, benches, chucks, blanks, speeds, accessories, circuits, dust conditions, service regions, skill and maintenance. They cannot prove population reliability, runout, finish, safe capacity, code compliance, service rate or injury prevention.Self-selected exact-model owners discuss delivery, setup, alignment, controls, vibration, accessories, maintenance, failures and service. Reports are configuration-specific anecdotes, not performance, defect, capacity or safety rates.
Price the complete working configuration and obtain electronic-service terms before choosing it over conventional belt and VFD designs
1 evidence recordSources
The page separates what a source states directly from what we conclude across sources.
Harvey identifies T-40 as a 14-by-24-inch bench or optional-leg lathe using a 1 HP industrial servo motor, 60 to 4,300 RPM control and a supported outboard-rest system.
Harvey lists T-40 at $2,399 against a $2,999 regular reference. Promotion can change; cast-iron legs, outboard support and 18-inch extension are separate, and freight is calculated at checkout
14-inch swing and 24 inches between centers, with documented optional extension and outboard-rest geometry. Base-machine dimensions do not include legs or the outboard working envelope. 1 HP industrial servo system with 60 to 4,300 RPM electronic control, forward and reverse and the exact manual's speed guidance. Servo torque does not override safe workpiece speed. 1-1/4-inch by 8 TPI spindle, MT2 tapers, spindle indexing and the manual's quill and 1-inch-class rest dimensions; check adapter shoulder and set-screw engagement on every chuck.
Harvey sells direct with current manual, contact and parts assistance. Confirm servo controller, motor, freight-return and warranty labor terms because local independent service may be limited. Retain the exact current product-page inventory; chuck, leg set, outboard support, extension, turning tools, collection and PPE are not implied by beauty photos or bundles.
AAW recommends a full face shield, conservative startup speed, slower speeds for larger or rough work, locked tailstock and tool-rest assemblies and no gloves, loose clothing, jewelry or untied hair.
OSHA identifies rotating parts, point-of-operation contact, flying chips and thrown work, and addresses close tool-rest placement, guards and entanglement controls. Application to a shop depends on workplace and operation.
OSHA notes high-velocity wood-dust emission and recommends close source capture. A lathe package does not establish exposure control or compliance.
An independent turner gives a product-specific first-impressions review of T-40 construction, controls and intended serious-turner use. Video impressions are not controlled durability testing.
Self-selected exact-model owners discuss delivery, setup, alignment, controls, vibration, accessories, maintenance, failures and service. Reports are configuration-specific anecdotes, not performance, defect, capacity or safety rates.
Neptune 15-Inch Digital Direct Drive Lathe is the smart direct-drive sliding and pivoting midi alternative at $1,499.99 current direct U.S. price.
JWL-1440VSK 14-Inch by 40-Inch Lathe with Legs is the long-bed sliding and pivoting reeves-drive floor lathe alternative at $2,749 current authorized U.S. price.
Manufacturer identity, exact current U.S. price, manual or specification, parts or support path, independent woodworking evidence and bounded owner or turner evidence were checked on August 20, 2026. This market covers complete current U.S.-supported benchtop, midi and full-size woodturning lathes for serious hobby and professional shops. It excludes metal lathes, duplicators and copy lathes, accessories, extensions and stands sold alone, unsupported imports, obsolete machines, cosmetic packages, chuck bundles and minor swing, bed or voltage siblings used only to pad the count. Preserve swing over bed and banjo, actual between-centers geometry, headstock and bed position, motor input and claimed output, voltage, phase, circuit and plug, belt ranges and electronic control, lowest usable speed, forward and reverse conditions, spindle thread and shoulder, taper, bore, indexing, quill and travel, fixed, sliding, swiveling and outboard paths, extension and rest support, weight, stand, floor, mobility and lifting, tool rest, banjo and tailstock behavior, included faceplate and centers versus required chuck, jaws, tools and sharpening, center alignment, runout, bed twist, setup and break-in, dust, chips, noise, electrical cooling, parts, warranty and service. A headline swing or horsepower figure does not approve a blank. Safe RPM depends on diameter, balance, soundness, mounting, drive and operator skill. Inspect stock and glue joints, rotate by hand, start at the lowest stable speed while standing out of the rotation plane, keep a locked rest close to the work and stop for vibration. Use impact-rated eye protection plus a full face shield, tie hair, remove loose clothing and jewelry and never wear gloves near rotating work. Guards, extraction, respiratory protection, hearing protection, electrical work, permits, workplace rules, fire control, rigging and training remain site-specific. Reverse can loosen threaded workholding unless positively secured as documented. Dust collection does not capture every chip or respirable particle. No manufacturer claim, capacity, price, review, owner report, drive feature, brake, jam sensor, guard, mounting system or service plan guarantees surface finish, runout, production capacity, uptime, code or workplace compliance, dust or noise control, workpiece retention, injury prevention or any safety outcome.
Researching another model?