Mountz · 070812
Ready to buy
The retained reference is $3,100.00 current U.S. manufacturer-direct price. Confirm the 100i range and required drive or rundown adapters because the integrated 17 mm female hex does not accept every torque tool directly. Verify the certificate, reaction path, socket or fixture, procedure, operator method, environmental state and independent check before controlled use.
Current market
Each line carries its own check date because price, software, specifications, and product cycle do not age at the same speed.
Confirm the 100i range and required drive or rundown adapters because the integrated 17 mm female hex does not accept every torque tool directly. Confirm stock, seller authorization, tax, delivery, case, batteries, charger, heads, sockets, adapters, sensors, cables, rundown fixture, mounting, software, calibration certificate, service and return terms before paying.
Choose EZ-TorQ III 100i for repeated low-torque tool checks when its 10 to 100 lbf-in range and interface fit the station and a portable transducer ecosystem is unnecessary.
Other paths
These are not generic competitors. Each one represents a different way to buy into the same market.
Tohnichi
Mountz
What changed
Older observations stay in the ledger when the current view changes. That lets a buyer tell the difference between an old complaint, an active issue, and a problem that was corrected.
EZ-TorQ III 100i Torque Analyzer was checked against manufacturer identity, manual and service, current U.S. price, range and accuracy basis, torque and angle behavior, head or fixture, alerts and data, power, environment, calibration, reaction safety, independent professional evidence and bounded owner or technician reports.
Each amount stays tied to its source and capture date. Conflicting prices remain visible until the seller resolves them.
Current reference priceA structured timeline will begin with the next source capture
Owner experience
Owner and technician evidence centers on low-range fit, backup-tester role, adapter selection, certificate handling and calibration support rather than a universal accuracy, joint-quality or reliability result.
These are self-reported, retailer-presented or forum observations across different fasteners, joints, lubrication, procedures, ranges, directions, sockets, heads, adapters, fixtures, batteries, software, environments, calibration programs, technicians and service access. They identify workflow and failure checks and do not establish standardized accuracy, uncertainty, traceability, clamp load, joint integrity, calibration interval, failure rate, service life, injury prevention, regulatory acceptance or liability outcomes.A metrology discussion identifies EZ-TorQ III and PTT use as range-specific backup and calibration equipment. It is bounded shop experience, not a current product validation or uncertainty statement.
Match the range and adapter to the tool population, then prove the station's repeatability with a documented loader and check standard before production release.
1 evidence recordSources
The page separates what a source states directly from what we conclude across sources.
Mountz identifies 070812 as a compact all-in-one low-torque tester with integrated transducer and ISO 17025 certificate for production screwdriver checks and small-tool verification.
$3,100.00 current U.S. manufacturer-direct price was retained for 070812. Confirm the 100i range and required drive or rundown adapters because the integrated 17 mm female hex does not accept every torque tool directly
The retained range is 10 to 100 lbf-in with the certificate and model-specific system accuracy controlling use; resolution, repeatability and overload capacity are separate limits This integrated model checks torque and tool behavior but is not retained as a torque-plus-angle wrench or joint-angle data system; use a compatible analyzer and sensor when angle is required Anchor the instrument, use the specified rundown adapter for powered tools, guard rotating interfaces and pinch points and never hold the analyzer by hand against tool reaction
Rigidly secure the analyzer and use the correct adapter or rundown fixture for the hand screwdriver, wrench or powered tool; direct hard-joint testing can produce a different result than the real assembly The display, target logic, modes and stored results support production checks with internal power and charger provisions; record export and station identification need confirmation for the exact configuration Use on a dry stable bench within the operating range, protect the hex and transducer from shock and overload and allow temperature stabilization after transport Mountz includes an ISO 17025 certificate and sells current calibration service; confirm accredited scope, points, uncertainty, interval and post-overload quarantine rather than treating the logo as universal coverage
Professional guidance explains that tester accuracy, supported range and mode, controlled loading, accredited calibration and a documented interval all bound a torque-verification result. It does not endorse a particular product.
Professional fastening coverage distinguishes installation torque from residual or breakaway audits and shows why technique, joint condition, angle data and operator training change the result.
Engineering guidance explains torque-plus-angle monitoring, data collection, fastening friction and torque-reaction controls. A recorded torque or angle value does not directly establish clamp load or joint integrity.
Professional guidance explains that tester accuracy, supported range and mode, controlled loading, accredited calibration and a documented interval all bound a torque-verification result. It does not endorse a particular product.
A metrology discussion identifies EZ-TorQ III and PTT use as range-specific backup and calibration equipment. It is bounded shop experience, not a current product validation or uncertainty statement.
TDT60CN3-G Digital Torque Screwdriver Tester is the mechanically loaded torque-screwdriver testing alternative at $4,054.00 current U.S. retail reference.
TorqueLab LTT250i Torque Analyzer is the expandable production torque analysis alternative at $3,985.00 current U.S. manufacturer-direct price.
Manufacturer identity, current U.S. price, specification, manual, calibration and service support, independent professional evidence and bounded owner or technician evidence were checked on August 19, 2026. This desk covers complete current professional electronic or digital torque wrenches, torque-and-angle hand tools and bench or portable torque analyzers used for controlled fastening, audit, intermediate check or verification. It excludes click-only mechanical wrenches, impact tools, torque sticks, simple adapters without a complete supported measurement workflow, unsupported imports, obsolete models, laboratory primary standards beyond this buyer boundary, bare transducers or displays without the retained required companions, minor range variants counted only as padding and cosmetic kits. Marked range is not automatically the calibrated or most accurate range. Accuracy may be percent of reading, percent of full scale or indicated value, may differ by direction and may apply only over a stated portion of capacity, temperature, angular speed or fixture. Torque and angle are process measurements and do not directly establish clamp load, preload, friction, joint seating, thread condition, material yield, leak tightness or structural integrity. Extensions, crowfeet, interchangeable heads, multipliers, reducers, flex positions, grip location, off-axis pull, socket fit, loading speed, rundown adapters, joint simulators, filter settings and fixture compliance change the result. Follow the product and fastener procedure, lubrication, sequence and reuse rules. A preset, light, tone, vibration or pass indicator does not prevent under-torque or over-torque. Electronic memory, app, Bluetooth, USB, timestamp, export or certificate does not by itself provide immutable traceability; control tool serial, operator, procedure revision, calibration status, configuration and file custody. Batteries, chargers, cables, connectors, software, firmware and service availability have life and compatibility limits. Respect temperature, humidity, condensation, liquid, chemical, conductive, explosive-atmosphere, electrostatic, shock and storage boundaries. Secure analyzers and reaction fixtures, use rated sockets and adapters, guard pinch and rotating points, support high-torque tools, maintain stable footing and keep the body out of the reaction path. Do not use a torque wrench as a breaker bar, impact tool or hammer, improvise a cheater, exceed capacity or continue after overload, impact or suspect readings. Disconnect power before fixture or sensor service and use qualified calibration and fastening procedures. No wrench, analyzer, certificate, calibration interval, check, app, report, preset, fixture, operator technique, support plan or warranty guarantees joint integrity, procedure correctness, measurement uncertainty, regulatory acceptance, traceability, reliability, injury prevention, property protection, product quality or any service, warranty or liability outcome.
Researching another model?